ge-interlogix simon 3 사용자 설명서
Simon Security System
18
Use the Table in Appendix B, which was filled out during the system planning, to help
program sensors.
program sensors.
¾
To add a hardwire or RF sensor or remote control:
Note
For a more specific location
name, press Option # for
compass directions (north,
northeast, east, southeast,
south, southwest, west,
northwest).
For a more specific location
name, press Option # for
compass directions (north,
northeast, east, southeast,
south, southwest, west,
northwest).
1.
Press Add. The panel announces “Select from Main Menu.”
2.
Press Sensor/Remote. The panel announces “Press button on sensor.”
3.
Press the sensor program button or release sensor tamper switch. The panel
announces “Keychain Remote. Press sensor again for next name or press Done to
select.”
announces “Keychain Remote. Press sensor again for next name or press Done to
select.”
Note
If you wish to use a sensor
number other than the next
one available, use the num-
bered keys to enter a 2 digit
sensor number immediately
after entering the sensor
type.
If you wish to use a sensor
number other than the next
one available, use the num-
bered keys to enter a 2 digit
sensor number immediately
after entering the sensor
type.
4.
Press Sensor/Remote repeatedly until you hear the name or item you want to use.
An alphabetical list of names the panel uses appears in Appendix B. Each name
may be used more than once.
An alphabetical list of names the panel uses appears in Appendix B. Each name
may be used more than once.
5.
Press DONE when you hear the desired name. The panel announces “Use num-
bered keys to enter sensor group.”
bered keys to enter sensor group.”
6.
Enter the 2-digit sensor group. The panel announces the sensor group and the first
available sensor number, then prompts you to press DONE to accept.
available sensor number, then prompts you to press DONE to accept.
7.
Press DONE. The panel confirms programming by announcing the sensor num-
ber, name, and group.
ber, name, and group.
¾
To delete sensors:
1.
Press Delete. The panel announces “Select from Main Menu.”
2.
Press Sensor/Remote repeatedly until you hear the name and number you want
deleted, then press DONE. The panel announces that the sensor is deleted.
deleted, then press DONE. The panel announces that the sensor is deleted.
X10 Module Operation
Use the following procedure to program X10 module operations into panel memory.
Notice that the Light Control button is used to program all X10 module operations
(light, appliance, and universal).
Notice that the Light Control button is used to program all X10 module operations
(light, appliance, and universal).
¾
To program the house code:
1.
Press Add.
2.
Press Light Control repeatedly until you hear the desired house code letter.
3.
Press DONE.
3
2
9
7
8
1
0
6
4
5
Test
System should be checked
422-2806 Rev A
Set
Code
Access
Clock
+
Delete
Delete
press
-
+
Hours
at least every three years.
To delete an option or access code
Hold key or press
and follow the voice
repeatedly until you
hear the desired item.
hear the desired item.
Note:
Cancel
and
Test
Cancel
DONE
Minutes
, then
DONE
See Note
If you make a mistake or want to
Sensor or Phone Test
follow the voice prompting.
To select a test, press
start over press
prompting.
by a qualified technician
Delete
START MENU
Add
Version 3
MAIN MENU
*
Remote
Sensor/
*
*
Control
Light
Option #
*
*
Sensors
-
*
Entry/Exit
Delay
CONTROL MENU
*
Press for program
information.
information.
Instruction
Add Option
Summary
Unit #
Add
Press
Clock Set
Press
Set Clock
DONE
Chime Voice
Latchkey Time
Panel Voice
Add
Option #
Press
Option #42:
Option #43:
Option #55:
Option #41:
Option #2:
Option #3:
Option #36:
Option #37:
See Note
Sensor Activated Light Lockout Start Time
Sensor Activated Light Lockout Stop Time
and follow voice prompts.
Pager Phone Number
Speaker Volume
Status Beep Volume
Option #1: Panel Beeps
use red numbers to enter 4-digit code.
Add Access Code
Hours
Access Code
See Note
Minutes
Time
Cancel