ONKYO SKM-540S Manual Do Utilizador
55
Advanced Setup
—Continued
Crossover Frequency
This setting only applies to the speakers that you speci-
fied as
fied as
Small
in the “Speaker Configuration” on page 54.
To get the best bass performance from your speaker sys-
tem, you need to set the crossover frequency according
to the size and frequency response of your speakers
tem, you need to set the crossover frequency according
to the size and frequency response of your speakers
Notes:
• For a more accurate setting, look up the frequency
response in the manuals supplied with your speakers
and set accordingly.
and set accordingly.
• Choose a higher crossover frequency if you want more
sound from your subwoofer.
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting (step 3) is set to Yes, and the
Front setting (step 4) is set to Large in the Speaker Con-
figuration on page 54.
put by feeding bass sounds from the front left and right
channels to the subwoofer. This function can be set only
if the Subwoofer setting (step 3) is set to Yes, and the
Front setting (step 4) is set to Large in the Speaker Con-
figuration on page 54.
7
Use the Down [
] button to
select “Surr Back,” and use the
Left and Right [
Left and Right [
]/[
] buttons to
select
Small
,
Large
, or
None
.
Small:
Select if the surround back
speakers are small.
Large:
Select if the surround back
speakers are large.
None:
Select if no surround back
speakers are connected.
Notes:
to None, this setting does not appear.
to Small, the Large option cannot be
selected.
selected.
8
Use the Down [
] button to
select “Surr Back Ch,” and use
the Left and Right [
the Left and Right [
]/[
] but-
tons to select
2ch
or
1ch
.
2ch:
Select if two (left and right)
surround back speakers are
connected.
surround back speakers are
connected.
1ch:
Select if one surround back
speaker is connected.
speaker is connected.
Note:
• If the Surround and Surr Back set-
tings in steps 6 and 7 are set to None,
this setting does not appear.
this setting does not appear.
Continue with step 9 of the “Crossover
Frequency” setting.
Frequency” setting.
9
Use the Down [
] button to
select “Crossover,” and then use
the Left and Right [
the Left and Right [
]/[
] but-
tons to select a crossover fre-
quency.
quency.
Use the diameter of the smallest
speaker in your system when choosing
the crossover frequency.
speaker in your system when choosing
the crossover frequency.
*Choose the setting suitable for the speaker.
Continue with step 10 of the “Double
Bass” setting below.
Bass” setting below.
10
Use the Down [
] button to
select “Double Bass,” and then
use the Left and Right [
use the Left and Right [
]/[
]
buttons to select:
On:
Double Bass function on.
Bass from the front left and
right channels is also fed to
the subwoofer (default).
right channels is also fed to
the subwoofer (default).
Off:
Double Bass function off.
11
Press the [SETUP] button.
Setup closes.
Speaker cone
diameter
Crossover
frequency
Over 8 in.
(20 cm)
40/50/60Hz*
6-1/2 to 8 in.
(16–20 cm)
80Hz
5-1/4 to 6-1/2 in.
(13–16 cm)
100Hz (default)
3-1/2 to 5-1/4 in.
(9–13 cm)
120Hz
Under 3-1/2 in.
(9 cm)
150/200Hz*
SETUP
HT-S790_En.book Page 55 Friday, February 17, 2006 3:28 PM