ONKYO SKM-540S Manual Do Utilizador
56
Advanced Setup
—Continued
The following table shows the display indicator for each
digital signal format.
digital signal format.
Normally, the AV receiver detects the signal format auto-
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can specify the signal format as either PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
matically. However, if you experience either of the fol-
lowing issues when playing PCM or DTS material, you
can specify the signal format as either PCM or DTS:
• If the beginnings of tracks from a PCM source are cut
off, try the PCM setting.
• If noise is produced when fast forwarding or reversing
a DTS CD, try the DTS setting.
When using progressive scanning on your DVD player,
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals. You can set it from 0 to 100 milliseconds
(ms) in 20 millisecond steps.
you may find that the picture and sound are out of sync.
With this setting, you can correct this by delaying the
audio signals. You can set it from 0 to 100 milliseconds
(ms) in 20 millisecond steps.
Note:
• This setting is not available when the Pure Audio lis-
tening mode is used, or the Direct listening mode is
used with an analog input signal.
used with an analog input signal.
Digital Input Signal Formats
Format
Display
Dolby Digital
DTS
PCM
1
Press and hold the AV receiver’s [DIGITAL
INPUT] button for about 3 seconds.
INPUT] button for about 3 seconds.
2
While “Auto” is displayed (about 3 sec-
onds), press the [DIGITAL INPUT] button
repeatedly to select: PCM, DTS, or Auto.
onds), press the [DIGITAL INPUT] button
repeatedly to select: PCM, DTS, or Auto.
PCM:
Only PCM format input signals will be
heard. If the input signal is not PCM, the PCM
indicator will flash and there will be no sound.
indicator will flash and there will be no sound.
DTS:
Only DTS format input signals will be
heard. If the input signal is not DTS, the DTS
indicator will flash and there will be no sound.
indicator will flash and there will be no sound.
Auto (default):
The format is detected automati-
cally. If no digital input signal is present, the
corresponding analog input is used instead.
corresponding analog input is used instead.
PCM
MASTER VOLUME
VIDEO
STANDBY
TONE
DISPLAY
STEREO
DIMMER
MEMORY
DIGITAL
INPUT
TUNING
MODE
A
B
SPEAKERS
TUNER
TAPE
VIDEO
3
VIDEO
2
VIDEO
1
VCR
DVD
MULTI CH
C D
SETUP
RETURN
CLEAR
LISTENING MODE
AUDIO
L
R
VIDEO
3
INPUT
STANDBY/ON
PHONES
TUNING
PRESET
ENTER
DIGITAL INPUT
Correcting Sound and Picture Sync
1
Press the [RECEIVER] REMOTE
MODE button.
MODE button.
2
Press and hold, for more than 4
seconds, the input selector but-
ton for the input source that you
want to correct.
seconds, the input selector but-
ton for the input source that you
want to correct.
This can be the [DVD], [VIDEO 1],
[VIDEO 2], or [VIDEO 3] input
source.
[VIDEO 2], or [VIDEO 3] input
source.
3
Use the Left and Right [
]/[
]
buttons to adjust the delay from 0
to 100 milliseconds in 20 milli-
second steps.
to 100 milliseconds in 20 milli-
second steps.
MUTING
PREVIOUS
MENU
GUIDE
TOP MENU
SP A / B
SETUP
RETURN
PLAYLIST/CAT
PLAYLIST/CAT
--/---
TAPE
M D/CDR
HDD
CABLE
ON/STANDBY
DIMMER
ENT
D TUN
SLEEP
10
11
12
INPUT SELECTOR
REMOTE MODE
V
1
V
2
V
3
C D
TAPE
TUNER
DVD
MULTI CH
T V
VOL
VOL
SAT
VCR
T V
DVD
RECEIVER
C D
INPUT
+10
0
CLR
1
2
3
4
5
6
7
8
9
ENTER
CH
DISC
ALBUM
RECEIVER
INPUT
SELECTOR
RECEIVER
V
1
V
2
V
3
DVD
1
2
3
6
HT-S790_En.book Page 56 Friday, February 17, 2006 3:28 PM