Puls QS20.241 Power Supply Guia De Especificação
QS20.241, QS20.241-A1, QS20.241-C1
Q-Series
24V,
20A,
S
INGLE
P
HASE
I
NPUT
10. L
IFETIME
E
XPECTANCY AND
MTBF
AC
100V
AC 120V
AC 230V
Lifetime expectancy
*)
54 000h
59 000h
71 000h
at 24V, 20A and 40°C
135 000h
143 000h
164 000h
at 24V, 10A and 40°C
153 000h *)
165 000h *)
200 000h *)
at 24V, 20A and 25°C
MTBF
**)
SN 29500, IEC 61709
407 000h
441 000h
469 000h
at 24V, 20A and 40°C
749 000h
799 000h
840 000h
at 24V, 20A and 25°C
MTBF
**)
MIL HDBK 217F
204 000h
215 000h
229 000h
at 24V, 20A and 40°C; Ground
Benign GB40
Benign GB40
273 000h
288 000h
308 000h
at 24V, 20A and 25°C; Ground
Benign GB25
Benign GB25
*) The Lifetime expectancy shown in the table indicates the minimum operating hours (service life) and is determined by the lifetime
expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specified in operational hours and is calculated according to the
capacitor’s manufacturer specification. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years
(131 400h). Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.
capacitor’s manufacturer specification. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years
(131 400h). Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.
**) MTBF stands for Mean Time Between Failure, which is calculated according to statistical device failures, and indicates reliability of a
device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent the life of a product.
The MTBF figure is a statistical representation of the likelihood of a device to fail. A MTBF figure of e.g. 1 000 000h means that
statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it can not be determined if the failed unit
has been running for 50 000h or only for 100h.
statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it can not be determined if the failed unit
has been running for 50 000h or only for 100h.
11. F
UNCTIONAL
D
IAGRAM
Fig. 11-1 Functional diagram
+
+
-
-
-
Output
Over-
Voltage
Protection
PFC
Converter
Output
Voltage
Regulator
Power
Converter
Output
Filter
DC-ok
Relay
Relay
Output
Voltage
Monitor
Output
Power
Manager
Temper-
ature
Shut-
down
Input Fuse
Input Filter
Input Rectifier
Active Inrush Limiter
Input Filter
Input Rectifier
Active Inrush Limiter
V
OUT
L
N
DC-ok
Contact
Contact
Overload
LED
DC-ok
LED
Oct. 2013 / Rev. 2.2 DS-QS20.241-EN
All parameters are specified at 24V, 20A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.
All parameters are specified at 24V, 20A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.
www.pulspower.com Phone +49 89 9278 0 Germany
10/26