Schneider Electric MGE Galaxy 5000 SUG580A90UL Manual Do Utilizador
Códigos do produto
SUG580A90UL
Page 3
12/10/13
6.
Input Surge Protection: UPS shall be equipped to withstand surges per
ANSI/IEEE C62.41.
ANSI/IEEE C62.41.
C.
AC Output Characteristics:
INSERT VOLTS BELOW.
1.
Voltage: [___] volts AC, ±1 percent steady state variation phase-to-phase voltage volts
AC, three-phase, 3 wires plus ground. 4 wire output shall be available through optional
transformer.
AC, three-phase, 3 wires plus ground. 4 wire output shall be available through optional
transformer.
2.
Frequency: 60 hertz, ±1.0 percent (or selectable up to 4 percent); 60 hertz, ±0.1 percent
when free running.
when free running.
3.
Voltage Regulation: ±1.0 percent for balanced load, ±1.75 percent for 50 percent
unbalanced load, ±2.5 percent for 100 percent unbalanced load.
unbalanced load, ±2.5 percent for 100 percent unbalanced load.
4.
Voltage Distortion: Maximum 2 percent total (THD) and 1 percent any single harmonic
on 100 percent linear loads.
on 100 percent linear loads.
5.
Voltage Transient (Step Load) Response: ±2 percent for load step changes from
100 percent to 0 and from 0 to 100 percent. The system returns to the ±1 percent range in
rms value in less than 100 ms.
100 percent to 0 and from 0 to 100 percent. The system returns to the ±1 percent range in
rms value in less than 100 ms.
6.
Voltage Recovery Time: Return to within 1 percent of nominal value within
16.67 milliseconds (one cycle).
16.67 milliseconds (one cycle).
7.
Phase Angle Displacement: 120 degrees, +1 degree for balanced load; 120 degrees,
+3 degrees for 100 percent unbalanced load.
+3 degrees for 100 percent unbalanced load.
8.
Non-Linear Load Capability: Output voltage total harmonic distortion shall be less than
3 percent when connected to a 100 percent non-linear load with a crest factor not to
exceed 3 percent.
3 percent when connected to a 100 percent non-linear load with a crest factor not to
exceed 3 percent.
9.
Slew Rate: 1.0 hertz/second maximum (or selectable up to 2.0 hertz/second).
10. Power Factor: 0.9 at the rated volt amperes (VA).
11. Inverter Overload Capability: 125 percent of rated load for 10 minutes, 150 percent of
11. Inverter Overload Capability: 125 percent of rated load for 10 minutes, 150 percent of
rated load for 1 minute.
12. Bypass Overload Capability: Greater than 212 percent for one cycle; greater than
150 percent for 1 minute.
D.
Battery:
1.
1.
Battery Voltage: 356 volts DC minimum before cutoff; 432 volts DC nominal; 490 volts
DC equalization voltage.
DC equalization voltage.
INSERT AMPERES BELOW.
2.
Maximum DC Current: Maximum DC current at cutoff voltage shall be [____] amperes.
3.
The battery charger is equipped with a temperature probe to enable temperature compensated
charging.
charging.
1.5 SUBMITTALS
A.
General: See [Section 01 33 00 - SUBMITTAL PROCEDURES]
[Section 01300 - SUBMITTALS].
[Section 01300 - SUBMITTALS].
B.
Product Data: Submit product data showing material proposed. Submit sufficient information
to determine compliance with the Drawings and Specifications. Product data shall include, but
shall not be limited to, the following:
1.
to determine compliance with the Drawings and Specifications. Product data shall include, but
shall not be limited to, the following:
1.
Catalog sheets and technical data sheets to indicate physical data and electrical
performance, electrical characteristics, and connection requirements.
performance, electrical characteristics, and connection requirements.
2.
Manufacturer’s installation instructions indicating application conditions and limitations of
use stipulated by product inspecting and testing agency. Include instructions for storage,
handling, protection, examination, preparation, installation, and starting of the product.
Include equipment installation outline, connection diagram for external cabling, internal
wiring diagram, and written instruction for installation.
use stipulated by product inspecting and testing agency. Include instructions for storage,
handling, protection, examination, preparation, installation, and starting of the product.
Include equipment installation outline, connection diagram for external cabling, internal
wiring diagram, and written instruction for installation.
C.
Shop Drawings: Submit shop drawings for each product and accessory required. Include
information not fully detailed in manufacturer’s standard product data, including, but not limited
to, complete electrical characteristics and connection requirements. Provide detailed equipment
information not fully detailed in manufacturer’s standard product data, including, but not limited
to, complete electrical characteristics and connection requirements. Provide detailed equipment