Инструкции Пользователя для Garmin Vector S

From the home screen, select   > Sensors > Add Sensor > 

Power.

Rotate the crank arm a few times.

When the sensor is paired with your Edge device, the sensor 

status is Connected. You can customize a data field to display 

Vector data.

Before you ride with Vector for the first time, you must enter the 

crank length, set the installation angle of the sensors inside the 

pedals, and calibrate the static zero reference. You must also 

calibrate the system if you move Vector to another bike.
These procedures contain instructions for the Edge 1000. If you 

, or go to 

The crank length is often printed on the crank arm.

Rotate the pedals a few times in order to activate Vector.

From the home screen, select   > Sensors >   > Sensor 

Details > Crank Length.

Enter the crank length, and select  .

Before you set the installation angles, you must set the Edge 

data fields to display power and cadence.

Go for a short ride on a trainer or on the road.

Ride until the cadence is nearly 70 rpm.

Accelerate smoothly to approximately 90 rpm.
When the installation angles are successfully set, a message 

appears and data fields display power data on the Edge 

device (1000, 810, and 510 only).

NOTE: During this task, the bike must be in an upright position, 

and nothing can be touching the pedals.

From the home screen, select the status bar or swipe down 

from the top of the screen.
The connections page appears.

Select   > Calibrate.
When the zero reference is determined, a message appears 

on the Edge device.

For best results, Garmin recommends calibrating Vector at the 

start of every ride.

Perform a static zero calibration.

Go for a ride.

This procedure contains instructions for the Edge 1000, 810, 

800, and 510 devices. If you have another compatible device, 

.

Hold a data field to change it.

Select a category.

Select a data field.

Vector measures pedal-based power.
Vector measures the force you apply a few hundred times every 

second. Vector also measures your cadence or rotational 

pedaling speed. By measuring the force, the direction of force, 

the rotation of the crank arm, and time, Vector can determine 

power (watts). Because Vector independently measures left and 

right leg power, it reports your left-right power balance.
NOTE: The Vector S system does not provide left-right power 

balance.

Some bike tools may scratch the finish of Vector components.

• Use wax paper or a towel between the tool and the 

hardware.

• After any bike adjustments, rotate the crank arm to check for 

clearance.

• Calibrate Vector at the start of every ride (

• Keep Vector components clean.
• When moving Vector to another bike, clean the threads and 

surfaces thoroughly.

• Go to 

 for the latest updates 

and information.

Your ride data or history is recorded to your Edge.
NOTE: History is not recorded while the timer is stopped or 

paused.
When the device memory is full, a message appears. The 

device does not automatically delete or overwrite your history. 

Upload your history to Garmin Connect™ periodically to keep 

track of all your ride data.

To prevent corrosion, thoroughly dry the USB port, the weather 

cap, and the surrounding area before charging or connecting to 

a computer.

Pull up the weather cap 

À

 from the USB port 

Á

.

Plug the small end of the USB cable into the USB port on the 

device.

Plug the large end of the USB cable into a computer USB 

port.

Go to 

.

Follow the on-screen instructions.

You can connect with your friends on Garmin Connect. Garmin 

Connect gives you the tools to track, analyze, share, and 

encourage each other. Record the events of your active lifestyle 

including runs, walks, rides, swims, hikes, triathlons, and more. 

To sign up for a free account, go to 

Store your activities: After you complete and save an activity 

with your device, you can upload that activity to Garmin 

Connect and keep it as long as you want.

Training

3