Roland v-synth xt 业主指南
184
Effects List
38: Phonograph
This effect reproduces the sound of an analog record played on a
record player. This includes the various noises with the characteristic
of records and the uneven rotation of older turntables.
record player. This includes the various noises with the characteristic
of records and the uneven rotation of older turntables.
fig.MFX-38
PS Grade
1–5
Sets the grade of the effect
sound.
The higher the value is set, the
more natural-sounding can be
obtained; however, this increas-
es the delay from the source
sound as well.
sound.
The higher the value is set, the
more natural-sounding can be
obtained; however, this increas-
es the delay from the source
sound as well.
PS Coarse
-12– +12 semi-
tone
tone
Specifies the pitch shift amount
in semitone steps.
in semitone steps.
PS Fine
-100– +100 cent
Adjusts the pitch shift amount in
2-cent steps (1 cent = 1/100 of a
semitone).
2-cent steps (1 cent = 1/100 of a
semitone).
PS Balance
DRY100:0WET–
DRY0:100WET
DRY0:100WET
Volume balance between the di-
rect sound (DRY) and the effect
sound (WET)
rect sound (DRY) and the effect
sound (WET)
Phaser Manual
0–127
Specifies the center frequency at
which the sound is modulated.
which the sound is modulated.
Phaser Rate
0.05–10.0 Hz,
note
note
Specifies the frequency of mod-
ulation.
ulation.
Phaser Depth
0–127
Specifies the depth of modulation.
Phaser Reso-
nance
nance
0–127
Specifies the amount of feed-
back for the phaser.
Higher settings will give the
sound a stronger character.
back for the phaser.
Higher settings will give the
sound a stronger character.
Phaser Mix Lev-
el
el
0–127
Specifies the volume of the
phase-shifted sound, relative to
the direct sound.
phase-shifted sound, relative to
the direct sound.
Delay Time
0–650 ms, note
Adjusts the delay time from the
direct sound until the delay
sound is heard.
direct sound until the delay
sound is heard.
Delay Feedback -98– +98%
Adjusts the proportion of the de-
lay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
lay sound that is fed back into
the effect. Negative (-) settings
will invert the phase.
Low Damp Freq 50–4000 Hz
Adjusts the frequency below
which sound fed back to the ef-
fect will be cut.
The Low Damp function damps
the low frequency band of the
delay sound quicker than other
bands, which makes for a clearer
delay effect.
which sound fed back to the ef-
fect will be cut.
The Low Damp function damps
the low frequency band of the
delay sound quicker than other
bands, which makes for a clearer
delay effect.
Low Damp Gain -36–0 dB
Degree of Low Damp
Hi Damp Freq
2000–20000 Hz
Adjusts the frequency above
which sound fed back to the ef-
fect will be cut.
High Damp, by attenuating the
higher frequencies first, makes
the delay sound more natural.
which sound fed back to the ef-
fect will be cut.
High Damp, by attenuating the
higher frequencies first, makes
the delay sound more natural.
Hi Damp Gain
-36–0 dB
Degree of High Damp
Delay Level
0–127
Volume of the delay sound.
Parameter
Value
Description
Parameter
Value
Description
Input Mode
MONO, STE-
REO
REO
Use this setting to select either a
stereo or monaural record play-
er for the effect.
stereo or monaural record play-
er for the effect.
Signal Dist
0–127
Degree of distortion
Frequency
Range
Range
0–127
Sets the frequency response of
the record player.
Lowering the value degrades
the frequency characteristics,
making the sound resemble that
from an older system.
the record player.
Lowering the value degrades
the frequency characteristics,
making the sound resemble that
from an older system.
Disk Type
LP, EP, SP
Sets the turntable rotation
speed.
LP: 33 1/3 r.p.m.
EP: 45 r.p.m.
SP: 78 r.p.m.
speed.
LP: 33 1/3 r.p.m.
EP: 45 r.p.m.
SP: 78 r.p.m.
Total Noise #1
0–127
Total noise level.
Scratch
0–127
Scratches on the record.
Dust
0–127
Dust on the record.
Hiss
0–127
Continuous hissing noise.
* These settings add the typical record’s noise. The noises increase as
the values are raised. Set each of the Scratch, Dust, and Hiss noise
levels to get a balance, the adjust the overall amount of noise with the
Total Noise Level control.
levels to get a balance, the adjust the overall amount of noise with the
Total Noise Level control.
Total Wow/
Flutter #2
Flutter #2
0–127
Total wow and flutter.
Wow
0–127
Wow, long cycle rotational ir-
regularity.
regularity.
Flutter
0–127
Flutter, short cycle rotational ir-
regularity.
regularity.
Random
0–127
Random rotational irregularity.
These settings determine the rotational irregularities of the record
player. Set each of the Wow, Flutter, and Random levels to get a bal-
ance, the adjust the overall depth of the effect with the Total Wow/
Flutter control.
Balance
player. Set each of the Wow, Flutter, and Random levels to get a bal-
ance, the adjust the overall depth of the effect with the Total Wow/
Flutter control.
Balance
DRY100:0WET–
DRY0:100WET
DRY0:100WET
Volume balance between the di-
rect sound (DRY) and the effect
sound (WET)
rect sound (DRY) and the effect
sound (WET)
L
R
Phonograph
V-SYNTH_XT_e2 184 ページ ２００５年３月２３日 水曜日 午後４時３９分