Korg triton-rack 信息指南

If you experience problems, refer to the relevant item 
and take the appropriate measures.

• Is the AC/AC power supply connected to an 

outlet? (

• Is the [POWER] switch turned on?

• Perform the following procedure. (

1 Press the [EXIT] key three times, and press the 

[GLOBAL] key.

2 Hold down the [EXIT] key, and press the 

[WRITE] key.

3 Rotate the [VALUE] dial to adjust the LCD 

screen.

• Are connections made correctly to your amp, 

• Is your amp or mixer turned on?
• The [OUTPUT] knob may have been turned all the 

way to the left. (

• If a specific track/timbre does not sound in 

Combination or Multi modes, make sure that its 
“Status” is set to INT or BTH. (

☞

• Are the Key Zone and Velocity Zone set so that 

sound will be produced? 

☞

• If there is no sound from the AUDIO OUTPUT 

(INDIVIDUAL) 1–4 jacks, make sure that “BUS 
Select” or “Bus Select” following the insert effect is 
set to 1, 2, 3, 4, 1/2, or 3/4. (

• In PROG 2.1: Ed–Basic, select the Prog Basic page, 

make sure that the “Hold” check box is unchecked. 
(

• Is your audio source connected to the AUDIO 

• Is the [INPUT] knob raised? (

• Is the [MIC/LINE] switch set appropriately? 

(

• If there is no sound in Sampling mode, go to SMPL 

1.1: Recording, select the Input/Pref page, and 
make sure that “Lvl” and “BUS” are set correctly. 
(

• If there is no sound in Program, Combination, or 

Multi modes, go to GLOBAL 1.1: System, select the 

Audio In page, and make sure that “Input1 Level,” 
“Input1 BUS Select,” “Input2 Level” and “Input2 
BUS Select” are set correctly. (

• If sound is still not input even after you have set 

“Input 1 Level,” “Input 2 BUS Select,” “Input 2 
Level,” and “Input 2 BUS Select” in the GLOBAL 
1.1: System, Audio In page, temporarily lower the 
“Input 1 Level” and “Input 2 Level,” and then 
move to Program, Combination, or Multi mode. 
Turn return to Global mode, and make the settings 
once again.

• When using an effect on the external audio source 

being input from AUDIO INPUT 1 and 2, 
oscillation may occur depending on the type of 
effect or on the parameter settings. Please adjust 
the input level, output level, and effect parameters. 
You need to be particularly careful when using a 
high-gain effect.

• After a sample edit has been executed, or after a 

stereo sample has been recorded, a small noise 
may be heard. This has no effect on the audio data 
that was edited or sampled.

• When using the BPM/MIDI Sync function to 

control the delay time of an effect, noise may occur 
in the delay sound. This noise is due to 
discontinuities in the delay sound, and is not a 
malfunction.

• Are the GLOBAL 1.1: System, Basic page “IFX1–5 

Off,” “MFX1 Off,” or “MFX2 Off” settings 
checked

• If you are in Combination, or Multi modes, and 

master effects are not applied when you raise the 
“S1 (Send1(MFX1))” or “S2 (Send2(MFX2))” of the 
timbre/track, does “Rtn (Return1)” or “Rtn 
(Return2)” from the master effect need to be 
raised? (

Alternatively, has “Send1” or “Send2” for each 
oscillator of the program used by the timbre/track 
been lowered? (

☞

The actual send level is determined by multiplying 
the send setting of each oscillator in the program 
with the send setting of the timbre/track.

• Are one or more SIMM modules installed? (

• Is there free memory area (

☞

Select a different memory bank. (

☞

Delete unneeded samples. (

☞

Save important samples before deleting them. (

☞