Panasonic dmc-lz10 操作指南
- 11 -
Others
[MEMORY CARD ERROR FORMAT THIS
CARD?]
The format of the card cannot be
recognised by this camera. Format the
card again with this camera.
Save your data to your computer, then use
this unit to reformat the card.
CARD?]
The format of the card cannot be
recognised by this camera. Format the
card again with this camera.
Save your data to your computer, then use
this unit to reformat the card.
[PLEASE TURN CAMERA OFF AND
THEN ON AGAIN]
This message appears when the camera
is not operating properly. Turn the camera
off and on. If the message persists, contact
the dealer or your nearest Service Centre.
[MEMORY CARD ERROR
MEMORY CARD PARAMETER ERROR]
Use a card compatible with this camera.
THEN ON AGAIN]
This message appears when the camera
is not operating properly. Turn the camera
off and on. If the message persists, contact
the dealer or your nearest Service Centre.
[MEMORY CARD ERROR
MEMORY CARD PARAMETER ERROR]
Use a card compatible with this camera.
You can only use 4 GB cards if they are
SDHC Memory Cards.
[MEMORY CARD ERROR
PLEASE CHECK THE CARD]
SDHC Memory Cards.
[MEMORY CARD ERROR
PLEASE CHECK THE CARD]
Failed access to the card. Insert the card
again.
again.
[READ ERROR
PLEASE CHECK THE CARD]
Data reading error.
Insert the card again. Make sure the card
is inserted properly and then play back
again.
[WRITE ERROR
PLEASE CHECK THE CARD]
Data writing error.
Turn the camera off and remove the card.
Then insert the card and turn the camera
on again. This error may also indicate that
the card is damaged.
[MOTION RECORDING WAS
PLEASE CHECK THE CARD]
Data reading error.
Insert the card again. Make sure the card
is inserted properly and then play back
again.
[WRITE ERROR
PLEASE CHECK THE CARD]
Data writing error.
Turn the camera off and remove the card.
Then insert the card and turn the camera
on again. This error may also indicate that
the card is damaged.
[MOTION RECORDING WAS
•
CANCELLED DUE TO THE LIMITATION
OF THE WRITING SPEED OF THE
CARD]
OF THE WRITING SPEED OF THE
CARD]
When you set the [PICTURE MODE]
to [30fpsVGA] or [30fps16:9], we
recommend using cards that offer 10
MB/second or higher speeds (shown on
their packages and elsewhere) for best
results.
Depending on the type of Card, recording
may stop in the middle.
to [30fpsVGA] or [30fps16:9], we
recommend using cards that offer 10
MB/second or higher speeds (shown on
their packages and elsewhere) for best
results.
Depending on the type of Card, recording
may stop in the middle.
[A FOLDER CANNOT BE CREATED]
A folder cannot be created because there
are no remaining folder numbers that can
be used.
Save your data to your computer, then use
this unit to reformat the card.
A folder cannot be created because there
are no remaining folder numbers that can
be used.
Save your data to your computer, then use
this unit to reformat the card.
If you execute [NO.RESET] in the [SETUP]
menu after formatting, the folder number is
reset to 100.
menu after formatting, the folder number is
reset to 100.
[PICTURE IS DISPLAYED FOR 4:3 TV]/
[PICTURE IS DISPLAYED FOR 16:9 TV]
[PICTURE IS DISPLAYED FOR 16:9 TV]
The AV cable is connected to the
camera. Press [MENU/SET] if you want
to delete this message at once.
Select [TV ASPECT] in the [SETUP]
menu to change the TV aspect.
camera. Press [MENU/SET] if you want
to delete this message at once.
Select [TV ASPECT] in the [SETUP]
menu to change the TV aspect.
This message also appears when the
USB connection cable is connected to
the camera only. In this case, connect
the other end of the USB connection
cable to a PC or a printer.
USB connection cable is connected to
the camera only. In this case, connect
the other end of the USB connection
cable to a PC or a printer.
[PRINTER BUSY]/[PLEASE CHECK
THE PRINTER]
THE PRINTER]
The printer cannot print. Check the printer.
•
•
•
•
•
■