Elica EVL43XS1 安装指导

 

key for 5 seconds, and after, the clock can be adjusted 

with the “+” and “-” keys. Colon “:” will flash indicating 

 

clock programming mode.

The user can have minute increments / decrements of 1 

minute, but if the user keep pressing the “+”/”-” keys 

 

for more than 1 second, the increments / decrements will 

 

be of 5 minutes. During this option the control will 

 

round to the nearest 5 minutes.

The user can finish on reprogramming the clock pressing 

the “timer” key.

After 1 minute of no key pressed the control will accept 

 

the programmed clock time and will add one minute 

 

to the set clock. 

After thirty fan functional hours, the display will show  

“Grease Filter” if the fan is active. When this icon is 

shown in the display, the grease filters installed are  

 

required to be washed.

To reset the grease filter saturation alarm the user must 

press the “+” key for 5 seconds, after this action the 

icon “grease filter” is not display, and the hood has the 

 

normal display operation. 

After one hundred and twenty functional hours of the fan, 

the display will show “Charcoal Filter” if the fan is active. 

When this icon flashes on display, the charcoal filters 

 

installed are required to be replaced or reactivated.

To reset the grease filter saturation indication the user 

must press the “-” key for 5 seconds, after this time 

the icon “charcoal filter” is not display and the hood has 

 

the normal display operation. 

The audible signals can be activated or deactivated 

pressing the “Light” key for 5 seconds.

If the audible signal is activated, a tone must sound and 

the “Snd” symbol must appear on the display for 2 second.

If the audible signal is deactivated, the “Snd” symbol must 

 

appear on the display for 2 second and no sound must sound.

The charcoal filter inclusion or exclusion can be set by 

pressing the “-” and “+” keys at the same time for 5 seconds.

The Inclusion or exclusion of charcoal filter must be  

selected while the lamps and the motor are OFF.

When the charcoal has been excluded, the charcoal filter 

 

alarm is disabled. 

The control is equipped with a heat sensor that will turn 

 

on the blower at second speed if excessive heat 

occurs (over 70°C) surrounding the control area.

If the blower is OFF or if it is operating at first speed, the 

 

blower will be set automatically to second speed.

During this state, the user may raise the blower speed to 

 

third speed but can not decrease the speed.

When the temperature level on the hood drops to normal, 

the blower will operate in the setting defined by the user 

 

before the alarm occured.

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

The metal filter traps grease released by foods on the cook-

top. The filter must always be installed when the hood is

operating / used.

 

Push the filter lock / pivot in direction to the center of the 

filter.

Once the pivot is pushed pull down the filter slowly.

 

Insert the filter tabs into the slots

Push the filter lock / pivot in direction to the center of the 

filter.

Once the pivot is pushed, raise the filter slowly until the 

 

top and release the pivot.

 

Swish the filter in hot soapy water and rinse in clean 

 

water or wash it in the dish washer.

Do not use abrasive cleaners. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clean with a damp, soapy cloth and dry with a clean cloth. 

A glass cleaner may also be used. 

ATTENTION: Do not wet the control panel.

Do not use a steel wool pad; it will scratch the surface.

To clean the stainless steel surface, use warm sudsy 

water, stainless steel cleaner or polish. Always wipe 

 

the surface in the direction of the grain. Follow the cleaner 

 

instructions for cleaning the stainless steel surface.

•

•

•

•

•

•

•

•

•

•