User ManualTable of ContentsWTK5504 v1.0 Touchscreen1User Manual1Home Screen5Arming and Disarming the System51. Close all sensors (i.e., stop motion and close doors). The Ready () indicator should be on.52. Press the Stay Arm button (and enter your Access Code) and do not leave the premises.5• A numeric keypad is displayed. Tap your access code.6• The Arming sequence is aborted and the system returns to the Home screen.6• The Armed LED turns OFF.6• The Home screen is displayed, indicating that the system is armed6• The Ready Indicator turns OFF.6• “Away Armed” is displayed in the Status Bar.61. Re-enter the premises.62. Enter your access code to disarm the system. You must do this before the entry delay timer expires.63. Follow the Away arming procedure again, making sure to close the entry/exit door properly.6Zone Status6Bypassed Zones7Emergency Key8Indicators8More Screen8More Functions Screens9Arming Modes91. Check that the Ready indicator is on.92. From the Home screen, press No Entry. The verbal prompt announces “No-entry arming in progress” and “Arming with No-entry delay” appears on the screen. The system is now armed in Stay mode.9System Chime (Chime Enable/Disable)10Quick Exit10Outputs10User Options11Access Codes111. The default attributes of a new code will be the attributes of the code used to enter User Programming whether it is a new code or an existing code being programmed.112. System Master Code 40 has attributes 3-4 ON by default.111. Select “Set Access Code”. A keypad screen is shown with the existing code. If there is no existing code, “AAAA” (or AAAAAA for 6 digits) is shown.122. Start to enter a new code. The code area will be cleared, and the new code will be shown. If the clear key is pressed, the new code will be cleared, but the old code is not deleted by this action. Once the last digit is entered the new code will h...121. Press the Access Code Programming button, then “Set Access Code”.122. Enter your desired 4- or 6-digit user access code.123. Press Prox Tag Programming.124. Place the prox tag near the tag reader at the top of the keypad to assign it to the user code. The message “Tag Enrolled Successfully” will be displayed and the keypad will beep. If the proximity tag has been enrolled previously, an error tone...121. Press More > User Options > Access Code Prog. [Master Code].122. Use left and right arrow buttons to select the user number associated with the proximity tag to be deleted and press Select.123. Press Delete User and confirm by pressing Yes.121. Press More > User Options > Access Code Prog. [Master Code].122. Use left and right arrow buttons to select the user number associated with the proximity tag and press Select.123. Choose “Replace Prox Tag” from the menu options.124. Place the prox tag near the tag reader at the top of the keypad. The message “Tag Enrolled Successfully” will be displayed and the keypad will beep.12Keypad Configuration131. Use the slide bar to select the desired brightness of the night light backlighting.132. To exit press the Back or Home button.131. A button toggles verbal options on and off. When Verbal Chime is set to on, the WTK5504 will speak the zone label words (e.g., ‘Laundry Room Window’) when the zone chimes. When Verbal Prompt is set to on, the WTK5504 will speak system prompts ...132. To exit press the Back or Home button.131. Select the desired language.142. To exit press the Back or Home button.14• Time and Date14• System Test14• Late to Open Programming14• Late to Open - On/Off14• Auto-Arm Programming14• Auto-Arm On/Off14• Enable DLS14• User Call-Up14• User Walk Test14Time & Date Programming141. To change the time/date press Time and Date. Tap on the section you would like to change and use the up/down arrows to change time/date.142. Once done, press Save. This is then confirmed by the “Settings Saved” screen.14System Test151. After pressing System Test, the keypad and system buzzer will sound an error tone for 2 seconds. After the buzzer stops sounding, the keypad will say “Test” at full volume, regardless of whether verbal chime or prompting are enabled and regard...152. To exit the function menu, press the Back button.151. Prior to testing, ensure that the system is disarmed and the Ready light is on.152. Close all zones to return the system to the Ready state.153. Perform a System Test by following the steps in the “Testing Your Keypad Sounder and Siren” section.154. Press More > User Options [Master Code] > User Functions > User Walk Test. To test the zones, activate each detector in turn (e.g., open each door/window or walk in motion detector areas).15Late-to-Open Programming15Late-to-Open On/Off15Auto-Arm Programming15• AC / DC Inhibit Arm16• Latching System Tampers16• Zone Expander Supervisory Fault16Auto-Arm On/Off16Enable DLS/Allow System Service16User Call-Up16Troubles16Alarms17When Alarm Sounds17• Temporal/pulsed siren = Fire Alarm17• 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide Alarm17• Continuous siren = Intrusion (Burglary Alarm)17Fire Alarm Pulsed Siren17Wireless Carbon Monoxide Alarm171. Operate silence button.172. Call emergency services or your fire department.173. Immediately move outdoors or to an open door/window.17Intrusion (Burglary) Alarm Continuous Siren181. If the alarm was accidental, enter your access code to silence the alarm. If the alarm system is disarmed within the programmed Abort window (check with the installer if this option has been enabled on your system and what transmitter delay time i...182. Following the Abort window is a 5-minute Cancel window, during which a user can enter their access code to cancel a previously transmitted alarm. A cancel signal will be transmitted to the Central Station and the screen will indicate “Communicat...18Sensor Reset18Reference Sheets19System Information19Sensor / Zone Information21Household Fire Safety Audit23Fire Escape Planning23IMPORTANT SAFETY INSTRUCTIONS2• Do not spill any type of liquid on the equipment.2• Do not attempt to service this product yourself. Opening or removing the cover may expose you to dangerous voltage or other risk. Refer servicing to qualified service personnel. Never open the device yourself.2• Do not touch the equipment and its connected cables during an electrical storm; there may be a risk of electric shock.2• Do not use the Alarm System to report a gas leak if the system is near a leak.2• Do not subject the touchscreen to mechanical shock (e.g., dropping or striking). Mechanical shock could damage the glass display.2• If the touchscreen glass is damaged, the liquid crystal fluid inside could leak out. Avoid contact with the liquid crystal fluid. If the liquid crystal fluid comes into contact with your skin or clothes, promptly wash it off using soap and water.2• Do not apply excessive force to the display surface or adjoining areas. Excessive force will distort the image on the display.2• Do not use hard or sharp implements to operate the touchscreen. Operating the touchscreen with any implement harder than a finger could scratch the display.2• Do not attempt to disassemble the LCD Module.2• If the display surface is contaminated, breathe on the surface and gently wipe it with a soft, dry cloth. If still not completely clean, moisten cloth with isopropyl alcohol.2• Clean the touchscreen with a soft cloth and isopropyl alcohol. Use of other cleaners such as water, ketone (e.g., acetone), and/or aromatic solvents (e.g., benzene and toluene) may damage the display. Do not use abrasives, water, thinners, solven...2About Your Security System2IMPORTANT NOTICE4Introduction4• Display 4.3" WVGA (800 ´ 480 pixel) color resistive touchscreen4• LED indicators 4 (Ready, Armed, Trouble, AC)4• “Night” light with adjustable brightness4• Dimensions (mounting) 5.5" x 3.6" x 1.0" [139.7 mm (L) x 91.4 mm (W) x 25.4 mm (D)]4• Horizontal viewing angle 130° (typ.)4• Vertical viewing angle 70° (top), 70° (bottom) (typ.)4• Brightness 400 cd/m24• Operating environment 0°C to 49°C (32°F to 120°F)4• Operating frequency 433.92 MHz4• 93% (max.) relative humidity non-condensing4• Display language(s) English, French, Spanish4Size: 1.19 MBPages: 28Language: EnglishOpen manual
