Honeywell International Inc. WFSLCDUI Manuale Utente
PRELIMINARY: Firelite Wireless Sensor Network P/N LS10036-000FL-E:N0 10/10/2013
47
W-DIS-D Operations
Wireless Display Driver (W-DIS-D)
Profile Configured
In this mode, the W-DIS-D is associated with the W-GATE but is not an active participant in the
mesh network. For further information on mesh formation, refer to, “4.6.3, "Mesh Formation". To
remove a profile from a W-DIS-D, refer to section, “3.6.3, "Removing Profiles".
mesh network. For further information on mesh formation, refer to, “4.6.3, "Mesh Formation". To
remove a profile from a W-DIS-D, refer to section, “3.6.3, "Removing Profiles".
In this mode, the W-DIS-D will be viewable in the communicator window of the PC tool with a
state of profile configured. The ANN-80 will display RF COMM LOSS when the W-DIS-D is at
factory default state.
state of profile configured. The ANN-80 will display RF COMM LOSS when the W-DIS-D is at
factory default state.
Modes of Operation as a Mesh Participant
Mesh Formation Mode
In this mode, the W-DIS-D is an active participant in a mesh that is forming. The LED flashes in
the following pattern: First blink green, second blink yellow for every 6.8 seconds. For further
information on mesh formation mode, refer to, “4.6.3, "Mesh Formation". The W-DIS-D will not
communicate directly with the tool for display in the communicator. The status of the W-DIS-D
must be obtained via the W-GATE. The ANN-80 will display ‘Mesh Formation in Progress’ during
mesh formation mode.
the following pattern: First blink green, second blink yellow for every 6.8 seconds. For further
information on mesh formation mode, refer to, “4.6.3, "Mesh Formation". The W-DIS-D will not
communicate directly with the tool for display in the communicator. The status of the W-DIS-D
must be obtained via the W-GATE. The ANN-80 will display ‘Mesh Formation in Progress’ during
mesh formation mode.
Initial Mesh Optimization Mode
In this mode, the mesh network is formed and is in the process of establishing stronger communica-
tion paths. The LED pattern flashes in the following pattern: A single yellow blink every 6.8 sec-
onds. For further information on initial mesh optimization mode, refer to the topic, "Initial Mesh
Optimization". The W-DIS-D will not communicate directly with the tool for display in the com-
municator. The status of the W-DIS-D must be obtained via the W-GATE. The ANN-80 will dis-
play Gateway Initializing during the initial mesh optimization mode.
tion paths. The LED pattern flashes in the following pattern: A single yellow blink every 6.8 sec-
onds. For further information on initial mesh optimization mode, refer to the topic, "Initial Mesh
Optimization". The W-DIS-D will not communicate directly with the tool for display in the com-
municator. The status of the W-DIS-D must be obtained via the W-GATE. The ANN-80 will dis-
play Gateway Initializing during the initial mesh optimization mode.
Normal Mode
In this mode, the mesh network formation is complete. The LED flashes in the following pattern: A
single green blink every 13.6 seconds. The LED flash can be disabled by panel configuration. If a
device is in trouble, it will be displayed at the ANN-80 or the FACP. For information, refer to
3.9.4, "Event Messaging". The W-DIS-D will not communicate directly with the tool for display in
the communicator. The status of the W-DIS-D must be obtained via the W-GATE. The ANN-80
will display the mesh ID when the system is normal, or will display a wireless event as specified in
3.9.4, "Event Messaging".
single green blink every 13.6 seconds. The LED flash can be disabled by panel configuration. If a
device is in trouble, it will be displayed at the ANN-80 or the FACP. For information, refer to
3.9.4, "Event Messaging". The W-DIS-D will not communicate directly with the tool for display in
the communicator. The status of the W-DIS-D must be obtained via the W-GATE. The ANN-80
will display the mesh ID when the system is normal, or will display a wireless event as specified in
3.9.4, "Event Messaging".
Rescue Mode
In this mode, devices that are active participants in the mesh search and retrieve the devices that
have lost the communication link. The rescue mode is indicated by the following LED pattern: One
green blink every 6.8 seconds. For more information on rescue mode refer to “2.7.1, "W-GATE
Modes of Operation" The W-DIS-D will not communicate directly with the tool for display in the
communicator. The status of the W-DIS-D must be obtained via the W-GATE.
have lost the communication link. The rescue mode is indicated by the following LED pattern: One
green blink every 6.8 seconds. For more information on rescue mode refer to “2.7.1, "W-GATE
Modes of Operation" The W-DIS-D will not communicate directly with the tool for display in the
communicator. The status of the W-DIS-D must be obtained via the W-GATE.
The ANN-80 will display the mesh ID when the system is normal, or will display a wireless event
as specified in 3.9.4, "Event Messaging".
as specified in 3.9.4, "Event Messaging".
SLC Operation
Program the point as a monitor point. When the communication to the ANN-80 is missing or dis-
rupted, the point will indicate open circuit. The monitor point will not initiate an alarm condition.
rupted, the point will indicate open circuit. The monitor point will not initiate an alarm condition.
3.8.2 W-DIS-D LED Indications
The two LEDs on the devices blink in the same pattern to allow the LED to be viewed from any
angle. The LED indications are provided in the table below.
angle. The LED indications are provided in the table below.