Инструкции для Mitsubishi Electronics Q25HCPU

Содержание

• COVER

  1
• SAFETY PRECAUTIONS

  2
• REVISIONS

  7
• INTRODUCTION

  8
• CONTENTS

  8
• About Manuals

  18
• How to Use This Manual

  19
• About the Generic Terms and Abbreviations

  20
• 1 OVERVIEW

  21
  • 1.1 Features

    22
• 2 SYSTEM CONFIGURATION FOR SINGLE CPU SYSTEM

  25
  • 2.1 System Configuration

    25
  • 2.2 Precaution on System Configuration

    30
  • 2.3 Confirming the Serial Number and Function Version

    32
• 3 GENERAL SPECIFICATIONS

  33
• 4 HARDWARE SPECIFICATION OF THE CPU MODULE

  35
  • 4.1 Performance Specification

    35
  • 4.2 Part Names and Settings

    38
  • 4.3 Switch Operation After Writing in Program

    41
  • 4.4 Latch Clear Operation

    42
  • 4.5 Executing Automatic Write to Standard ROM.

    42
• 5 POWER SUPPLY MODULE

  44
  • 5.1 Specification

    44
    • 5.1.1 Power supply module specifications

      44
    • 5.1.2 Selecting the power supply module

      49
    • 5.1.3 Precaution when connecting the uninterruptive power supply

      51
  • 5.2 Names of Parts and Settings

    52
• 6 BASE UNIT AND EXTENSION CABLE

  55
  • 6.1 Base Unit Specification Table

    55
  • 6.2 Extension Cable Specification Table

    57
  • 6.3 Parts Names of Base Unit

    57
  • 6.4 Setting the Extension Base Unit

    60
  • 6.5 I/O Number Allocation

    61
  • 6.6 Guideline for Use of Extension Base Units (Q5[ ] B)

    62
• 7 MEMORY CARD AND BATTERY

  66
  • 7.1 Memory Card Specifications

    66
  • 7.2 Battery Specifications (For CPU Module and SRAM Card)

    67
  • 7.3 Handling the Memory Card

    68
  • 7.4 The Names of The Parts of The Memory Card

    69
  • 7.5 Memory Card Loading/Unloading Procedures

    70
  • 7.6 Installation of Battery (for CPU Module and Memory Card)

    71
• 8 EMC AND LOW VOLTAGE DIRECTIVE

  72
  • 8.1 Requirements for Conformance to EMC Directive

    72
    • 8.1.1 Standards applicable to the EMC Directive

      72
    • 8.1.2 Installation instructions for EMC Directive

      73
    • 8.1.3 Cables

      74
    • 8.1.4 Power supply module

      76
    • 8.1.5 When using QA1S6[ ] B type base unit

      76
    • 8.1.6 Others

      79
  • 8.2 Requirement to Conform to the Low Voltage Directive

    80
    • 8.2.1 Standard applied for MELSEC-Q series PLC

      80
    • 8.2.2 MELSEC-Q series PLC selection

      80
    • 8.2.3 Power supply

      81
    • 8.2.4 Control box

      81
    • 8.2.5 Grounding

      82
    • 8.2.6 External wiring

      82
• 9 LOADING AND INSTALLATION

  83
  • 9.1 General Safety Requirements

    83
  • 9.2 Calculating Heat Generation by PLC

    88
  • 9.3 Module Installation

    91
    • 9.3.1 Precaution on installation

      91
    • 9.3.2 Instructions for mounting the base unit

      94
    • 9.3.3 Installation and removal of module

      97
  • 9.4 How to Set Stage Numbers for the Extension Base Unit

    101
  • 9.5 Connection and Disconnection of Extension Cable

    102
  • 9.6 Wiring

    105
    • 9.6.1 The precautions on the wiring

      105
    • 9.6.2 Connecting to the power supply module

      108
• 10 MAINTENANCE AND INSPECTION

  109
  • 10.1 Daily Inspection

    110
  • 10.2 Periodic Inspection

    111
  • 10.3 Battery Replacement

    112
    • 10.3.1 Battery life

      113
    • 10.3.2 Battery replacement procedure

      115
• 11 TROUBLESHOOTING

  117
  • 11.1 Troubleshooting Basics

    117
  • 11.2 Troubleshooting

    118
    • 11.2.1 Troubleshooting flowchart

      118
    • 11.2.2 Flowchart for when the "MODE" LED is not turned on

      119
    • 11.2.3 Flowchart for when the "MODE" LED is flickering

      120
    • 11.2.4 Flowchart for when the "POWER" LED is turned off

      121
    • 11.2.5 Flowchart for when the "RUN" LED is turned off

      122
    • 11.2.6 When the "RUN" LED is flickering

      123
    • 11.2.7 Flowchart for when the "ERR." LED is on/flickering

      123
    • 11.2.8 When the "USER" LED is turned on

      124
    • 11.2.9 When the "BAT." LED is turned on

      124
    • 11.2.10 Flowchart for when the "BOOT" LED is flickering

      125
    • 11.2.11 Flowchart for when output module LED is not turned on

      126
    • 11.2.12 Flowchart for when output load of output module does not turn on

      127
    • 11.2.13 Flowchart for when unable to read a program

      128
    • 11.2.14 Flowchart for when unable to write a program

      129
    • 11.2.15 Flowchart for when it is unable to perform boot operation from memory card

      131
    • 11.2.16 Flowchart for when UNIT VERIFY ERR. occurs

      132
    • 11.2.17 Flowchart for when CONTROL BUS ERR. occurs

      133
  • 11.3 Error Code List

    134
    • 11.3.1 Procedure for reading error codes

      134
    • 11.3.2 Error Code List

      135
  • 11.4 Canceling of Errors

    153
  • 11.5 I/O Module Troubleshooting

    154
    • 11.5.1 Input circuit troubleshooting

      154
    • 11.5.2 Output Circuit Troubleshooting

      157
  • 11.6 Special Relay List

    158
  • 11.7 Special Register List

    180
• APPENDICES

  216
  • APPENDIX 1 Error Code Return to Origin During General Data Processing

    216
    • APPENDIX 1.1 Error code overall explanation

      216
    • APPENDIX 1.2 Description of the errors of the error codes (4000H to 4FFFH)

      217
  • APPENDIX 2 External Dimensions

    222
    • APPENDIX 2.1 CPU module

      222
    • APPENDIX 2.2 Power supply module

      222
    • APPENDIX 2.3 Main base unit

      225
    • APPENDIX 2.4 Slim type main base unit

      227
    • APPENDIX 2.5 Extension base unit

      228
  • APPENDIX 3 Upgraded Functions of High Performance Model QCPU

    231
    • APPENDIX 3.1 Specification comparison

      231
    • APPENDIX 3.2 Function comparison

      231
    • APPENDIX 3.3 Added functions and the corresponding GX Developer versions

      232
• INDEX

  233
• WARRANTY

  235