Справочник ПользователяСодержаниеSAFETY PRECAUTIONS3CONDITIONS OF USE FOR THE PRODUCT10REVISIONS11INTRODUCTION13CONTENTS13ABOUT MANUALS21HOW THIS MANUAL IS ORGANIZED23HOW TO USE THIS MANUAL24GENERIC TERMS AND ABBREVIATIONS25PRECAUTIONS FOR USE26CHAPTER1 OVERVIEW271.1 Features29CHAPTER2 SYSTEM CONFIGURATION342.1 System Configuration342.1.1 Precautions for system configuration372.2 Configuration of Peripheral Devices382.3 Checking Serial Number and Function Version39CHAPTER3 GENERAL SPECIFICATIONS41CHAPTER4 CPU MODULE434.1 Performance Specifications434.2 Part Names454.3 Switch Operation after Writing a Program474.4 Reset Operation48CHAPTER5 POWER SUPPLY MODULE505.1 Specifications505.2 Precaution when connecting the uninterruptible power supply525.3 Names of Parts and Settings53CHAPTER6 BASE UNIT556.1 Specification556.2 Part Names56CHAPTER7 BATTERY577.1 Battery (Q6BAT)577.1.1 Battery Specifications577.1.2 Installation of Battery58CHAPTER8 CPU MODULE START-UP PROCEDURES598.1 Procedure before Operating in SAFETY MODE59CHAPTER9 EMC, LOW VOLTAGE, AND MACHINERY DIRECTIVES629.1 Requirements for Conformance to EMC Directive629.1.1 Standards relevant to the EMC Directive639.1.2 Installation in a control panel649.1.3 Cables659.1.4 Power Supply Module689.1.5 Others689.2 Requirement to Conform to the Low Voltage Directive709.2.1 Standard applied for MELSEC-QS series programmable controller709.2.2 MELSEC-QS series programmable controller selection709.2.3 Power supply719.2.4 Control panel719.2.5 External wiring739.3 Requirements for compliance with the Machinery Directive74CHAPTER10 LOADING AND INSTALLATION7510.1 Calculating Heat Generation of programmable controller7710.2 Module Installation7910.2.1 Installation precautions7910.2.2 Instructions for mounting the base unit8610.2.3 Installation and removal of module8910.3 Wiring9210.3.1 Wiring precautions9210.3.2 Connecting to the power supply module96CHAPTER11 MAINTENANCE AND INSPECTION9711.1 Daily Inspection9911.2 Periodic Inspection10011.3 Battery Life and Replacement Procedure10111.3.1 Battery lives of CPU modules10211.3.2 Replacement Procedure of the CPU Module Battery10411.4 When programmable controller Has been Stored without a Battery10611.5 When Battery Has Gone Flat during Storage of a programmable controller107CHAPTER12 TROUBLESHOOTING10812.1 Troubleshooting Basics10812.2 Troubleshooting Flowchart10912.2.1 Troubleshooting category flow10912.2.2 Flowchart for when the ERR terminal (negative logic) is off (opened)11012.2.3 Flowchart for when the "POWER" LED turns off11212.2.4 When the "ALIVE" LED does not turn on or turns off11412.2.5 Flowchart for when the "RUN" LED turns off11612.2.6 When the "RUN" LED flashes11712.2.7 Flowchart for when the "ERR." LED turns on or flashes11812.2.8 When the "USER" LED turns on12112.2.9 When the "BAT." LED turns on12212.2.10 Flowchart for when a program cannot be read12312.2.11 Flowchart for when a program cannot be written12412.2.12 Flowchart for when the CPU cannot communicate with the GX Developer12512.3 Error Code List12712.3.1 Error codes12812.3.2 Reading an error code12912.3.3 Error code list (1000 to 1999)13012.3.4 Error code list (2000 to 2999)13612.3.5 Error code list (3000 to 3999)14212.3.6 Error code list (4000 to 4999)15212.3.7 Error code list (5000 to 5999)15612.3.8 Error code list (8000 to 9000)15812.4 Clearing an error17212.5 Error codes returned to request source during communication with CPU module17512.6 Special Relay List18412.7 Special Register List190APPENDICES209Appendix 1 External Dimensions209Appendix 1.1 CPU module209Appendix 1.2 Power supply module210Appendix 1.3 Main base unit211Appendix 2 Safety CPU Module Upgrade212Appendix 3 Precautions for Battery Transportation214Appendix 4 Handling of Batteries and Devices with Built-in Batteries in EU Member States215Appendix 4.1 Disposal precautions215Appendix 4.2 Exportation precautions216INDEX218WARRANTY220Размер: 3,8 МБСтраницы: 224Язык: EnglishПросмотреть