Benutzerhandbuch für Magnetek TM7310rev01

Inhaltsverzeichnis

• Technical Manual

  1
• Introduction

  12
  • Drive Ratings and Specifications

    12
    • Basic Drive Specifications

      12
    • Service Conditions

      12
  • Software Operating Features

    12
  • Drive Model Numbers

    13
• Quattro startup guide

  14
  • Initial Inspection

    14
    • Unpacking

      14
    • Installation

      14
  • Grounding considerations

    15
  • Initial adjustments after power up

    15
    • Encoder Set-up

      15
    • Motor Parameter Set-up

      15
    • Hoist way Parameter Set-up

      15
    • Line voltage setup

      16
    • Auto tune Procedure

      16
    • (C1, C2, C3, C4) configuration setup

      16
    • Low speed inspection mode

      16
• Interconnections

  17
  • Encoder Connections

    19
    • Logic Inputs

      19
    • Analog Inputs

      20
    • Logic Outputs

      21
    • Relay Outputs

      21
    • Solid State Relay Outputs

      21
    • Analog Outputs

      22
• Drive Sequencing

  23
  • NORMAL operating sequence

    23
  • ABNORMAL Operation Sequence

    24
  • Quattro Pre-Charge

    24
• Drive Operation and Feature Overview

  25
  • Analog Velocity Follower

    25
  • Preset Speed & Profile Generator

    25
  • Serial Link Follower

    25
  • Pre-Torque

    25
  • Torque Feed Forward

    25
  • Torque/Current Ramp-Down

    25
  • Motor Field Current Control and Field weakening

    26
  • DSPR

    26
  • Over-Speed Test

    26
  • Fault & Alarm Reset

    26
  • Electronic Motor Over-Load

    26
  • Armature Voltage Feedback

    26
  • Status Indicator Lights

    27
  • MONITOR / Adjust / Set-up Parameters:

    27
• Parameters

  28
  • Parameter Introduction

    28
  • Menu Navigation

    29
    • Navigation at the Menu Level

      29
    • Navigation at the Sub-menu Level

      29
    • Navigation at the Entry Level

      29
    • Hidden Parameters

      29
  • Parameter Tree

    30
• Adjust A0 menu

  32
  • Drive A1 submenu

    32
    • GAIN CHNG LEVEL

      38
      • SPD DEV LO LEVEL and SPD DEV HI LEVEL

        39
      • RUN DELAY TIMER

        39
      • ROLLBACK GAIN

        39
      • NOTCH FILTER FRQ

        40
  • S-Curves A2 submenu

    41
  • Multistep Ref A3 submenu

    43
  • Motor Side Power Convert A4 submenu

    45
  • Line Side Power Converter A5 submenu

    48
  • Motor Parameters A6 submenu

    49
    • OVLD TIME OUT

      50
• Configure C0 menu

  52
  • User Switches C1 submenu

    52
    • HI/LO GAIN SRC

      61
      • Elevator Speed Regulator (Ereg)

        61
      • PI Speed Regulator

        62
      • Ramp Stop Select

        62
  • Logic Inputs C2 submenu

    63
  • Logic Outputs C3 submenu

    65
  • Analog Outputs C4 submenu

    67
• Display D0 menu

  68
  • Elevator Data D1 submenu

    68
  • MS Power Data D2 submenu

    70
  • LS Power Data D3 submenu

    71
• Utility U0 menu

  72
  • PASSWORD

    73
    • HIDDEN ITEMS

      73
      • UNITS

        73
      • OVERSPEED TEST

        73
      • RESTORE DFLTS

        74
      • MS DRIVE INFO

        75
      • MS CUBE ID Screen

        76
      • LS DRIVE INFO

        76
        • LS TYPE Screen

          76
      • LS CUBE ID Screen

        77
      • HEX MONITOR

        77
• Fault F0 menu

  78
  • ACTIVE FAULTS

    78
    • FAULT HISTORY

      79
      • FAULT COUNTERS

        79
• Maintenance

  80
  • Maintenance Overview

    80
  • Drive Servicing

    80
• Troubleshooting

  81
  • Bad Serial Connection

    83
    • Noise or Bad Connector Connection

      83
      • Bad Connector Connection

        83
        • Improper drive On-Run-Stop sequencing

          84
        • Check parameter settings and contactor

          84
        • Parameters Corrupted

          84
        • Hardware Problem

          84
        • Problem with Motor Contactor

          84
        • Loss of gate power supply

          84
        • Parameters Corrupted

          84
        • Confirm Speed Command Polarity

          84
        • Excessive Field Weakening

          85
        • Encoder Phasing Should Match Motor Rotation

          85
        • Encoder Power Supply Loss

          85
        • Accurate Parameters

          85
        • Response of Speed Regulator

          85
        • Encoder Coupling Sloppy or Broken

          85
        • Excessive Noise on Encoder Lines

          85
        • Hardware Problem

          85
        • Check Parameter Settings

          85
        • Possible bad current sensor

          86
        • Check Parameter Settings

          86
        • Incorrect Wiring

          87
        • Drive and/or Motor is Undersized

          87
        • Check Parameter Settings

          87
        • Problem with Motor Contactor

          88
        • Loss of gate power supply

          88
        • Parameters Corrupted

          88
    • Overcurrent Problem

      89
      • Excessive Field Weakening

        89
        • Parameters Corrupted

          91
        • Contactor Problem

          92
        • Contactor Problem

          92
        • Parameters Corrupted

          92
        • Verify Overload Curve Parameters

          92
• Appendix

  97
  • Auto Tune Procedure

    97
  • Inertia Calculation

    98
    • Using the Software to Estimate the System’s Inertia

      98
  • EMC Compliance

    99
  • Re-Assembly Procedure for 200A / 250A drives

    100
  • Control Power Consumption

    104
  • Watts Loss

    104
  • Input / Output Ratings

    104
  • Wire Terminal Specs

    105
  • Dimensions / Weights

    106
  • Component Locations

    111
  • Spare Parts Quattro DC Drive

    118
• Index

  121